Products

Car dual radio adapter automotive harness cable factory

Specifications for this item

Model No: KY-C112

Product Name: Automotive wire harness

①FAKRA double female straight connector 8.0 pitch, white 5.0 copper tube six-piece set (Huaxing Tongda)

②φ5.5*15 Black Heat Shrinkable Tube

φ1.0*3 black heat shrinkable sleeve

③ Sticker with QR code / running code “Fox dual radio cable XP01V0739R0″ synthetic paper (polypropylene) black characters on white background (length: 100mm width: 20mm)

④φ4.6 black {[(11/0.16TS+HDPE white ID:2.6mm)*1C+aluminum foil]+braided wire (16/3/0.12TS)}+PVC without printing L=140mm

⑤FAKRA male connector type B white 5.0 copper tube four-piece set (Huaxing Tongda)

⑥FAKRA male connector Z type black 5.0 copper tube four-piece set (Huaxing Tongda)


Product Detail

Product Tags

Requirements:

1. Retention force of wire and antenna terminal: ≥5.0KG. Retention force of antenna shell and terminal: ≥3.5KG.

TEST:

1. a.100% conduction, short circuit, open circuit, dislocation, insulation withstand voltage test;

b. Insulation resistance: ≥10MΩ, DC 500V, 0.01S;

c. On resistance: ≤3Ω;

d. Withstand voltage: AC 350V I: 1mA T: 0.1S;

2. Instantaneous short circuit test time ≥ 3 seconds.

Picture-7
Picture-6
gPicture-4

Package:

1. The product is bundled with PE film every 25PCS, and the labels should be stacked neatly.

2. The product is packed in white transparent PE bags (the quantity is based on the actual quantity), the width is: 324mm, the thickness: 0.06mm. (Part No.: 3040016101) The length is subject to the actual demand length. The opening is folded in half and sealed with transparent glue. After installation, a Philosopher for delivery label is attached to the middle position.

3. The product is packed in a medium-sized carton 48.5*34*22CM H838D (part number 3010002202) (the packing quantity is subject to the actual quantity); after packing, stick the lable of feige customer on the upper left corner of the side of the outer box.

Remarks:

1.The outer jacket of P1 end should be peeled to 17±1mm, cut the braid cleanly, keep the ground wire, and cover the 0.8*15mm sleeve; the both middle jacket are stripped 5~6mm, twisted into a ground wire, and covered with 0.8*10mm sleeves respectively; The middle incision is sleeved with 2.0*8mm and 2.5*8mm respectively.It is appropriate to cut the length of the ground wire. firstly weld a single core wire and ground wire, and cover the welding legs with 1.5*8mm sleeves respectively. Then weld other core wires, and cover the welding legs with 1.5*5mm sleeves respectively, and the sleeves cover the solder joints for heat shrinkage.

2. The outer jacket of P2 end should be peeled to 34±1mm ,cut the braid cleanly, keep the ground wire, and cover the 0.8*31mm sleeve; the two middle jacket are stripped 7~8mm, twisted into ground wire, and covered with 0.8*22mm sleeves respectively; The middle incision is sleeved with 2.0*15mm and 2.5*15mm sleeves respectively. It is appropriate to cut the length of the ground wire. After drying the outer tube,and then injection the SR,and the tube which is close to the signal should be dried tightly.


  • Previous:
  • Next:

  • Write your message here and send it to us